EXTRACTED TEXT FROM: 同发科技19颗4合一彩屏带调焦LED摇头灯英文 .doc

 19 LED dyeing Lamp





Instructions for use

     

        Thank you for using the products produced by our company. In order to use this product safely and effectively, please read this instruction manual carefully and completely before using this product. This manual contains: the performance characteristics of the productTruePlease keep the instructions and how to install it safely, as well as the important information of use.,In order to use the time referenceSet an examination. Please strictly follow the relevant instructions when installing and using.

    Product description:
19 LED dyeingLamp, shake your headDyeA new revolution! Lighter...The total quality is only 11Kilogram!Faster...The X/Y axis moves faster, runs smoother and makes less noise! The software has a correction and positioning function to make up for hardware errors, and the positioning accuracy is quite high!Thoroughly solve X/YCalmNo.Standard! Brighter...4All-in-one optical lens combination,16CH channel: 24 CH channel.
  
Technical parameters:
Power supply: AC100V-240V
Frequency: 50Hz-60Hz
Total power:220W
Fuse:TenA
LampFountainheadPower:200W
Color temperature: 8500K
Average life: 2000H
Control signal: international standard DMX512
Outward appearance:High-temperature resistantPlastic+ Molded alloy material
Lamp body color: black
Protection level: IP20
 Net weight 11. Kilogram

Function introduction:
1.International standard control letterHowl:DMX512
2.Number of roads:21CH,29CHChannel.
3.MotorQuantity: Total3 silent motors
4. ColourLiquidBrilliant650,000-color TFT interface,Easy to operate, interfaceArtistic, the interface is180-degree reversal display.
5.X-axis levelRevolve540℃,YVertical axisTurn270℃,With automatic correction and positioning.
6. X,YThe shaft operation can be adjusted and finely, and the software has correction and positioning.Function,High accuracy!
7.TransferLight:0-100% linearRegulate.
8.RepeatedlyDodge: strobeVelocity(1-30 times/second),Full linear dimming and variable strobe speedLinear measure.
9.TransferBurnt: Using optical combination, the effect is far better than usual.DyeThe lamp can project high-definition.Result.
10.Overheating intelligenceProtect
11.Intellectual abilityDimmingAccuseCut out (Extension light FountainheadService life)

Connection of DMX512 signalCome into contact with:
This lamp uses DMX512 signal control.Model,The control signal of each lamp belongs to a parallel relationship, and there are many connections.YouIt is best to use dual-core shielded cables for lamp signals. When connected, each lamp passes through the DMX signal on the lamp.Socket(CannonSeat) INPUT (input) and OUTPUT (output) are connected, and the 3-core XLRXL plug terminals connecting the signal line of the lamp must correspond to each other.,When connecting the lamp signal,It is recommended to use DMX signal end.Terminal.It can be avoided to destroy the control signal due to electric dry sound.,DMX signal terminal is aSelfXLR plugTaxiConnect one between 2 feet and 3 feetSelf120 ohms1WThe resistance of,And connect it to the last lamp.TaxiOUTPUT (output))SocketUp.

Calculation method of the starting address code of the lamp:
The starting address code of the current lamp is equal to (the starting address code of the previous lamp) + (the channel of the lampNumber) Explanation:
1: The starting address code value of the first lamp is A001.
2The basic number of channels of the controller should be greater than or equal to the total number of channels used by the lamp..
3:PourDesireWhen using any controller, each lamp must have its own starting address code, if the firstYouThe starting address code of the lamp is set A001, the lampThe number of roads is16CH; Then the starting address of the second lampCode justSet to A017; The starting address code of the third lamp is set.ForA033; soReason by analogy,(This setting method also requiresRootAccording to different consoles.)


Installation instructions for lamps:
This lamp can be placed horizontally.,Be sure to pay attention to the installation method when hanging obliquely and upside down.
1.Fixing lamps and lanternsFix:Before positioning the lamp,To ensure the stability of the installation site,When reversing the hanging,You must make sure that the lamp does not fall on the support frame.,Use safety ropes to pass through the support frame and lamp handles for auxiliary hanging.;To ensure safety.Prevent lamps from falling and sliding,During the installation and debugging of lamps,Pedestrians are not allowed to pass below.,Regularly check the safety rope isDenyWear and tear,Is the hook screw loose?,If all the consequences arising from the falling of the lamp due to the unstable installation of the hanging, the manufacturer shall not bear any responsibility..

Safety tips!
To ensure the safe and correct use of lamps,Please read the following safety tips carefully before use to avoid unnecessary failure and injury..
1.Non-professionalPersonnelDo not remove the lamps and accessories in the lamps without authorization..
2.ACentigradePower supply:Check whether the local power supply meets the product's rated voltage requirements.
3.This lamp is according to the type of electric shock protection.Design,The lamps should be connected to a fully grounded power supply system, andLampThe ground line must be connected to the ground line of the power supply system..Please do notSendUse the damaged power supply of the insulation layerThread,Same as noNoConnect the power cord to other wires..
4.The lamps are being installed and positioned.Season,Keep a minimum distance between any point on the surface of the lamp and any burnable explosive material isTenMeter,Distance from the irradiated object 2.5Meter,Please do not install the lamps directly.In theOn the surface of burning material.
5.The ambient temperature of the lamp: (-10 degrees + 40 degrees),The highest temperature on the surface of the lamp is 80Linear measure,Lamps should stay away from liquids.AndWet ringBorder.
6.Make sure that the lamps are well grounded before using them.Good,Do not install and remove any parts of the lamp with electricity..
7.Install lightsTime to time,The fixing screws must be fastened.,And add a safety cable and check it regularly.
8.It is recommended not to exceed the continuous working hours of lamps.Guo10 smallSeasonThe interval between the continuous start-up lamps should not be less than10 points. DenyIt will not be triggered normally due to the overheating protection of the light bulb.
9.UsedCheng Zhong,If the lamp is abnormal, you should stop using the lamp in time.
10.The light bulb should be timely when it reaches its rated service life.RenewOtherwise, there will be a dangerous accident of bubbles..
11.The rotating parts and pasted accessories of the lamps must be checked regularly.CheckIf there is a loosening, shake and strengthen it in time to prevent accidents.
12.The lamps are made of strong wind.Cold,It is easy to accumulate dust and must be cleaned once a month, especially the heat dissipation air outlet.,DenyThen it willDue to the accumulation of dust and blockage, the heat dissipation is poor, which makes the lamp abnormal..


RaiseProtection and protectionRaise:
Shut down operation: before each shutdown,Put the light in advance.FountainheadShut.Let the heat dissipation fan use the lamp inside.SeasonThe heat generated is quickly discharged, which can prolong the accessories in the lamp.,Especially the lamp.FountainheadThe service life! To ensure that the lamps can run stably,It should be kept clean.,Take apart the lamps for repair or start maintenance.WorkshopBefore this, confirm whether the power is disconnected.,It is very important to keep the lamps clean.,Please clear it regularly.Jie,It not only maintains the maximum brightness output, but also extends the service life of the lamps.,It is recommended to use high-quality glass cleaner and clean soft cloth for cleaning.,Use a vacuum cleaner to clean the interior of the lamp at least once every six months..
After-sales service
Take notice of!When the lamps leave the factory, they have undergone strict quality inspection and the packaging is intact. Please follow the instructions..
Machine failure caused by human causes is not covered by the warranty..
1.The company provides technical advice to customers throughout their lives.Ask.
If the product appearsBlock,When it needs to be repaired, please show the product warranty card.,And fill in the relevant content truthfully..At the same time, we also hope that customers can feedback the problems of the product to us in time, so that we can improve the product as soon as possible.
2.Remove the lampExternal,The following accessories are also available.:
Attachment:Power cord:1Strips, signal lines:1. Instructions: 1Part
Optional parts
LampFountainhead(According to the customerDemand)
Lamp hook safety cable(According to the customerChoose)

Software specialSpot:
 1, High intelligence:For example, check whether Hall and optocoupler are wrong in the reset. Reset calibration (zero calibration),X-axis, Y-axis,Focus.
   
Interface description:Main interface


 
3.2. Setting interface
Be an optionExplain
       


 System settings 
DMX address001-512   Slaw status: Receive the DMX signal from the console or host by pressing"Certain"The key enters the editing state. At this time, 100 digits are selected, press"Up"Low position or rank"Key to change the address code. Press it again."Certain"Key to select ten editors. Press it again."Certain"Key to select a bit to edit. Press again to exit the editing state.Encoder Open Use the encoder (optocoupler) to judge the stride and automatically correct the position
 Shut Do not use an encoder (optocoupler) to correct the positionUnknownTurn overEmbellish one's speech with literary quotationsTurn off/onY reversalTurn off/on
Operation modeOperation modeDMX/voice control/automaticChannel selection21CH 29CH      
Display settingsLanguage selectionChinese, EnglishInverted screen settingsOn/offFactory settingsX-axis calibration128Y-axis calibration128Focus calibration128Red200Green200Blue200White200Logo selection000

3.6 . InvertedInterface
Push down"Certain"Key, the interface can180-degree reversal display.
3.7 . EnglishInterface
Push down"Certain"Key, the interface switch to English mode.
3.8 . ChineseInterface
Push down"Certain"Key, interface switch to Chinese modelStyle.
Channel mode:
211X-axis (horizontal)000-2552Y axis (vertical)000-2553XY speed000-2554Total dimming000-2555Red(R) Group 1000-2556Green (G) Group 1000-2557Blue (B) Group 1000-2558White (W) Group 1000-2559Strobe000-255TenFocus000-25511Functional mode000-25512Functional modeVelocity000-25513X-axis fine-tuning000-25514Y-axis fine-tuning000-25515Reduce(255)000-25516CTO000-25517LED auxiliary light self-propelled000-25518LED auxiliary light self-propelled speed000-25519LED auxiliary light red000-25520LED auxiliary light green000-25521LED auxiliary light blue000-255              



291X-axis (horizontal)000-2552Y axis (vertical)000-2553XY speed000-2554Total dimming000-2555Red(R) Group 1000-2556Green (G) Group 1000-2557Blue (B) Group 1000-2558White (W) Group 1000-2559Red(R) Group II000-255TenGreen (G) Group 2000-25511Blue (B) Group 2000-25512White (W) Group 2000-25513Red(R) Group 3000-25514Green (G) Group 3000-25515Blue (B) Group 3000-25516White (W) Group 3000-25517Strobe000-25518Focus000-25519Functional mode000-25520Functional modeVelocity000-25521X-axis fine-tuning000-25522Y-axis fine-tuning000-25523Reduce(255)000-25524CTO000-25525LED auxiliary light self-propelled000-25526LED auxiliary light self-propelled speed000-25527LED auxiliary light red000-25528LED auxiliary light green000-25529LED auxiliary light blue000-255
3.9.Technical parameters:
Voltage: AC100~240V 50/60HZ
 Power: 220W
 Lamp beads: 19 3535*RGBW10W lamp beads can be controlled in 3 laps, and 38 5050 RGB*0.2W lamp beads can be controlled separately
Control mode: DMX512, self-propelled, master-slave, with RDM function.
Channel: CH21, CH129,
Dimming: 32bit 0~100% linear dimming
Features: Dyeing+Flash +Point control
Operating temperature: -30 degrees to 50 degrees
Strobe frequency: 1~30HZ
Appearance: metal, black
Connection method: DMX512 input and output / power input and output.
IP level: IP20
 Size: Weight:





